" notice to proceed scarpe and remove loose paint on the bottom 2-0"" of the lower masonry area exterior of all front window sashes and surrounds front entry and dentil molding. Caulk joints and repaint to match the previous paint color. Complete the sa"

Replace existing gas fired steam boiler with same size & location - burnham 7 0 btu utilize existing water line backflow etc as per code.

Repair chimney; repoint three sides of chmney at property line using flamingo brixament colored masonry cement type n; where brick is missing install bricks that match the original as closely as possible in size color and hardness; install chimney cove

"remove paint from windows (sashes and frames) on rear north and west elevations: repair/restore in-kind where needed: paint bm # oc-25 ""cloud cover"" match front facade windows. Remove existing inappropriate cementitious mortar from north (rear) elevation"

Remove paint from south elev (address side) of building facade include brick sandstone & wood portico windows & frames. As per code.

Increase single phase service from 2 amps to 6 amps 120/2 volts install 3-2 amp main ckt breaker panels 2- 2 1/2 conduits for service entrance conductors and grounding and bonding as required. Relocate exist single phase ckts to new panels.

Install wiring for a/c units to include 1-125 amp feeder 3 sub panels 4-branch circuits to air handlers 4-branch circuits to condensing units install out door gfci receptacles at condensing units.

Install (2) 2 1/2 ton split a/c system with complete ductwork to condition third floor office and bedrooms. Install 0 btu mitsubishi ductless heat pump unit to condition third floor chets office. Install 3 1/2 ton mitsubishi ductless heat pump unit t

Remove paint from windows (sashes and frames) on rear north and west elevations: repair/restore in-kind where needed: paint bm # oc-25 "cloud cover" match front facade windows. Remove existing inappropriate cementitious mortar from north (rear) elevation repoint with flamingo brixament mortar match existing mortar color type n. Re-paint fire escape in rear bm # 2132- low lustre (black) all as per specification submitted as per code

Repair chimney; repoint three sides of chmney at property line using flamingo brixament colored masonry cement type n; where brick is missing install bricks that match the original as closely as possible in size color and hardness; install chimney cover. Work done to code.

Notice to proceed scarpe and remove loose paint on the bottom 2-0" of the lower masonry area exterior of all front window sashes and surrounds front entry and dentil molding. Caulk joints and repaint to match the previous paint color. Complete the same process at wood windows doors and frames on the rear and west side of the building and at the clerestory windows; scrape clean prime and paint the front entry metal handrail; scrape and paint metal gate on west side of facade; repair four entry columns including the removal of paint and the recoat with white mineral coating; repair and repaint damaged balustrades and panels at the roof by repairing salvageable wood components and replacing deteriorated components with a non-rot material similar to azek or boral. New elements must replicate the profiles of the existing trim.

Install (2) 2 1/2 ton split a/c system with complete ductwork to condition third floor office and bedrooms. Install 0 btu mitsubishi ductless heat pump unit to condition third floor chets office. Install 3 1/2 ton mitsubishi ductless heat pump unit to condition second floor chets kitchen.

Remove paint from windows (sashes and frames) on rear north and west elevations: repair restore in-kind where needed: paint bm # oc-25 "cloud cover" match front facade windows. Remove existing inappropriate cementitious mortar from north (rear) elevation repoint with flamingo brixament mortar match existing mortar color type n. Re-paint fire escape in rear bm # 2132- low lustre (black) all as per specification submitted as per code

Install (2) 2 1 2 ton split a c system with complete ductwork to condition third floor office and bedrooms. Install 0 btu mitsubishi ductless heat pump unit to condition third floor chets office. Install 3 1 2 ton mitsubishi ductless heat pump unit to condition second floor chets kitchen.

Install wiring for a c units to include 1-125 amp feeder 3 sub panels 4-branch circuits to air handlers 4-branch circuits to condensing units install out door gfci receptacles at condensing units.

Increase single phase service from 2 amps to 6 amps 120 2 volts install 3-2 amp main ckt breaker panels 2- 2 1 2 conduits for service entrance conductors and grounding and bonding as required. Relocate exist single phase ckts to new panels.