Structural restoration services will remove and replace the vertical sealant at the precast-to-brick joint at the center precast stack at the east side of the building approx. 336 linear feet total. The new material will consist of normanco soft rod bac

Non structural alterations: exterior work: per chap: notice to proceed: repoint areas on the east west and south elevations not to exceed 4 linear feet. New mortar will match the existing color texture composition and tooling. Remove and replace

Securring the existing fence. Per chap: notice to proceed: install pour rock line post footers to stabalize 23 loose fence posts along the front terrace wall and cover all 23 footers with black abs plastic shoes image of black plastic shoes attached. The

Notice to proceed replacement of damaged covering for awning at the main front entrance to the building. New canopy retains existing canopy structure.

Replace existing controller and disconnect with new same size & same location as per code.

Replace existing heat pump system (for common area) as per code.

Replace commercial gallon gas hot water heater 3 0 btu. As per code.

Replace water main a service pipe asper code.

Structural restoration services will remove and replace the vertical sealant at the precast-to-brick joint at the center precast stack at the east side of the building approx. 336 linear feet total. The new material will consist of normanco soft rod backer rod and tremco dymonic fc urethane sealant over the backer rod. The work will be accomplished using a skyclimber swing stage with an alpha 10 series motor. This project is necessary to correct a problem with water intrusio into condominum units from rain storms. As per code

Securring the existing fence. Per chap: notice to proceed: install pour rock line post footers to stabalize 23 loose fence posts along the front terrace wall and cover all 23 footers with black abs plastic shoes image of black plastic shoes attached. The fence is ornamental iron with apowder coated medium gloss finish 65 linear feet. 18 inches high. As per code.

Non structural alterations: exterior work: per chap: notice to proceed: repoint areas on the east west and south elevations not to exceed 4 linear feet. New mortar will match the existing color texture composition and tooling. Remove and replace and replace bulging brick on the north end of the west wall. New brick will match sample images provided to chap staff. 7 sq ft as per code.

Notice to proceed complete the following work on the northeast elevation. - remove and replace all window perimeter sealants. Materials to be used are nomaco sof-rod backer rod tremco dymonic 1 and vulkem 171 primer. Remove and replace all bathroom/kitchen vent perimeter sealants. Remove and replace all spandrel-to-brick joint sealants at the bottom of the spandrels only. Repair concrete spandrel spalls and rout and seal the perimeter of the repairs. Material to be used is united states concrete products (uscp) thin patch vo. Repair micellaneous minor concrete spalls 18 locations. Remove mortar and install caulk along the ac block-to brick transition approximately 76 lf. Repoint brick masonry. Material to be used is brixment type n colored masonry cement. Remove and replace 27 cracked brick. New bricks to match existing. Prepare and apply two (2) coats of acrylic waterproof coating to the face of the spandrels. Material to be used is basf masterprotect el 750. Original permit descrip

Authorization to proceed replace two storefront entries to the north and south of the front entrance of the property. The storefronts will match the existing with the use of a bronze finish. Property is non-contributing to the historic district.

Mount vernon historic district - remove existing railing and awning supports at deli entrance core drill holes to accommodate the new railing and awning supports and install new aluminum pipe railing and awning support. Railings and awning supports will be factory-coated black finish. All work to be completed as per plans in chap files.

Authorization to proceed remove front entry bi-fold doors and replace with new automatic swing doors in dark bronze finish frame. All work to match information on file with chap.

Notice to proceed complete the following work on the northeast elevation. - remove and replace all window perimeter sealants. Materials to be used are nomaco sof-rod backer rod tremco dymonic 1 and vulkem 171 primer. Remove and replace all bathroom kitchen vent perimeter sealants. Remove and replace all spandrel-to-brick joint sealants at the bottom of the spandrels only. Repair concrete spandrel spalls and rout and seal the perimeter of the repairs. Material to be used is united states concrete products (uscp) thin patch vo. Repair micellaneous minor concrete spalls 18 locations. Remove mortar and install caulk along the ac block-to brick transition approximately 76 lf. Repoint brick masonry. Material to be used is brixment type n colored masonry cement. Remove and replace 27 cracked brick. New bricks to match existing. Prepare and apply two (2) coats of acrylic waterproof coating to the face of the spandrels. Material to be used is basf masterprotect el 750. Original permit descrip

Notice to proceed: at southeast corner of the building demolish and replace two sidewalk slabs. At the deli steps remove and rest two bricks and repoint mortar joints. At the northeast corner of the building rout the existing mortar joint between the knee wall and building and install sealant. At the northeast corner of the building rout and seal the crack in the top step riser. At the northeast corner of the building partially repoint the four knee stair walls an allowance of 73 sf is included. All work to match information on file with chap.

Notice to proceed: provide swing stage access to the exterior of unit 2206. Demolish the brick masonry from the bottom of the top spandrel beam to the top of the bottom spandrel beam. Cut out and repoint 100% of the concrete masonry unit (cmu) mortar joints in the exposed area. Install aluminum thru wall flashing at the top of the bottom spandrel beam. Install flashing membrane to the cmu and the new aluminum thru wall flashing. Install aluminum jamb and sill flashing at the two small inside windows and end dams the full height at both ends of the extent of the work area. Apply elastomeric bitumen air and vapor barrier membrane to the cmu surface overlapping the new counter flashing and the window and door jamb flashings. Seal the frame-to -flashing joint with silicone building sealant at both ends of the extent work and around the perimeter of the two inside windows. Rebuild the brick veneer using the previously approved bricks and type n colored mortar. Install sealant at the bottom