WILLIAM J RABOIN

137-141a Newbury St Boston Ma 02116
Strip roof to concrete deck. Install 3-inch poly-iso insulation to deck and secure to roof. Glue a . 060 carlisle rubber roof membrane to entire roof area approximately 1200 square feet. We will cut out protrusions as we go. Install a new roof drain. Rubber flash 3 large skylights. Install pourable p

137 141a Newbury St Boston Ma 02116
Strip roof to concrete deck. Install 3-inch poly-iso insulation to deck and secure to roof. Glue a . 0 carlisle rubber roof membrane to entire roof area approximately 12 square feet. We will cut out protrusions as we go. Install a new roof drain. Rubber flash 3 large skylights. Install pourable pitch pockets to all a. C. Units. Cut into masonry on wall on four sides as a raglet. Install . 032 bronze colored heavy duty metal to all four walls. Pre-drill metal and rubber under the metal every foot to hold rubber in place. Seal and secure metal. Not visble from any public way

38 Saint Botolph St Boston Ma 02116
Top roof main part above option: we propose the following year carlisle roofing system: clean all loose debris from roof. Remove all existing metal. Install pressure treated lumber on bottom edge with 6-inch width 7 8-inch thick to all four sides as well as outside front on main on opposite side of parapet wall. Install 1- inch poly-urethane insulation board with an r-factor of approximately 5. 6 (not the 1 2inch recovery board that has no r-factor rating and which we in the field have found to be substandard) over roof area and screw down using disks and screws. Lay out . 0 rubber roof membrane cutting out all protrusions as we go such as: soil pipes penthouses skylights etc. Fold back rubber apply bonding adhesive to both insulation and to rubber membrane. Wait until tacky about 15 minutes. Then fold rubber over insulation to form a tight seal. - install pre-molded vent pipe boots to vent pipes where possible. - rubber flash all chimneys skylights and protrusions on roof with rubber fl

121 Newbury St Boston Ma 02116
Re: 121 newbury street boston ma (back 4th floor) note: all work to be done on rear of building note: its very difficult to access this job. Its four flights up and we have to deal with using fire escapes. Owner needs to make sure all cars are removed during demolition and slate work. The second row of cars may be brought back when the metal work begins (after a couple of days). Strip all slate and metal flashings. Install grace water & ice to entire exposed area. Install slate (not re-using existing slate but will match size and color). Remove window trim on upper and lower left and right sides of 3 windows including roof. Step flash left and right sides on the ends. Install a piece of lead at the top. Install all new window trim (same style as existing ogee style or we could install a flat style) in black . 0 metal extra heavy gauge). Install roof above each of the 3 window in . 0 black metal. On bottom edge of mansard theres a 10-foot gutter. Remove gutter. Install new fascia. Install

176 Newbury St Boston Ma 02116
Re: flat roof approximately 37x25. We propose the following year carlisle roofing system: strip off existing roof system. Clean all loose debris from roof. Install 1- inch poly-urethane insulation board with an r-factor of approximately 5. 6 (not the 1/2inch recovery board that has no r-factor rating and which we in the field have found to be substandard) over roof area and screw down using disks and screws. Lay out . 0 rubber roof membrane cutting out all protrusions as we go such as: soil pipes penthouses skylights etc. Fold back rubber apply bonding adhesive to both insulation and to rubber membrane. Wait until tacky about 15 minutes. Then fold rubber over insulation to form a tight seal. - install pre-molded vent pipe boots to vent pipes where possible. - rubber flash all chimneys skylights and protrusions on roof with rubber flashing. - install a pressure treated wood edge nailer. Install . 032 heavy gauge metal to outside edges of roof and seal all nails with rubber edge flashing. -

137141a Newbury St Boston Ma 02116
Strip roof to concrete deck. Install 3-inch poly-iso insulation to deck and secure to roof. Glue a . 0 carlisle rubber roof membrane to entire roof area approximately 12 square feet. We will cut out protrusions as we go. Install a new roof drain. Rubber flash 3 large skylights. Install pourable pitch pockets to all a. C. Units. Cut into masonry on wall on four sides as a raglet. Install . 032 bronze colored heavy duty metal to all four walls. Pre-drill metal and rubber under the metal every foot to hold rubber in place. Seal and secure metal. Not visble from any public way

979 South St Roslindale Ma 02131
Strip and re-roof. Take down unused chimney.

137 141a Newbury St Boston Ma
Strip roof to concrete deck. Install 3-inch poly-iso insulation to deck and secure to roof. Glue a . 0 carlisle rubber roof membrane to entire roof area approximately 12 square feet. We will cut out protrusions as we go. Install a new roof drain. Rubber flash 3 large skylights. Install pourable pitch pockets to all a. C. Units. Cut into masonry on wall on four sides as a raglet. Install . 032 bronze colored heavy duty metal to all four walls. Pre-drill metal and rubber under the metal every foot to hold rubber in place. Seal and secure metal. Not visble from any public way

176 Newbury St Boston Ma
Re: flat roof approximately 37x25. We propose the following year carlisle roofing system: strip off existing roof system. Clean all loose debris from roof. Install 1- inch poly-urethane insulation board with an r-factor of approximately 5. 6 (not the 1/2inch recovery board that has no r-factor rating and which we in the field have found to be substandard) over roof area and screw down using disks and screws. Lay out . 0 rubber roof membrane cutting out all protrusions as we go such as: soil pipes penthouses skylights etc. Fold back rubber apply bonding adhesive to both insulation and to rubber membrane. Wait until tacky about 15 minutes. Then fold rubber over insulation to form a tight seal. - install pre-molded vent pipe boots to vent pipes where possible. - rubber flash all chimneys skylights and protrusions on roof with rubber flashing. - install a pressure treated wood edge nailer. Install . 032 heavy gauge metal to outside edges of roof and seal all nails with rubber edge flashing. -

979 South St Roslindale Ma
Strip and re-roof. Take down unused chimney.

38 Saint Botolph St Boston Ma
Top roof main part above option: we propose the following year carlisle roofing system: clean all loose debris from roof. Remove all existing metal. Install pressure treated lumber on bottom edge with 6-inch width 7 8-inch thick to all four sides as well as outside front on main on opposite side of parapet wall. Install 1- inch poly-urethane insulation board with an r-factor of approximately 5. 6 (not the 1 2inch recovery board that has no r-factor rating and which we in the field have found to be substandard) over roof area and screw down using disks and screws. Lay out . 0 rubber roof membrane cutting out all protrusions as we go such as: soil pipes penthouses skylights etc. Fold back rubber apply bonding adhesive to both insulation and to rubber membrane. Wait until tacky about 15 minutes. Then fold rubber over insulation to form a tight seal. - install pre-molded vent pipe boots to vent pipes where possible. - rubber flash all chimneys skylights and protrusions on roof with rubber fl

121 Newbury St Boston Ma
Re: 121 newbury street boston ma (back 4th floor) note: all work to be done on rear of building note: its very difficult to access this job. Its four flights up and we have to deal with using fire escapes. Owner needs to make sure all cars are removed during demolition and slate work. The second row of cars may be brought back when the metal work begins (after a couple of days). Strip all slate and metal flashings. Install grace water & ice to entire exposed area. Install slate (not re-using existing slate but will match size and color). Remove window trim on upper and lower left and right sides of 3 windows including roof. Step flash left and right sides on the ends. Install a piece of lead at the top. Install all new window trim (same style as existing ogee style or we could install a flat style) in black . 0 metal extra heavy gauge). Install roof above each of the 3 window in . 0 black metal. On bottom edge of mansard theres a 10-foot gutter. Remove gutter. Install new fascia. Install

137141a Newbury St Boston Ma
Strip roof to concrete deck. Install 3-inch poly-iso insulation to deck and secure to roof. Glue a . 0 carlisle rubber roof membrane to entire roof area approximately 12 square feet. We will cut out protrusions as we go. Install a new roof drain. Rubber flash 3 large skylights. Install pourable pitch pockets to all a. C. Units. Cut into masonry on wall on four sides as a raglet. Install . 032 bronze colored heavy duty metal to all four walls. Pre-drill metal and rubber under the metal every foot to hold rubber in place. Seal and secure metal. Not visble from any public way

176 Newbury St Boston Ma
Re: flat roof approximately 37x25. We propose the following year carlisle roofing system: strip off existing roof system. Clean all loose debris from roof. Install 1- inch poly-urethane insulation board with an r-factor of approximately 5. 6 (not the 1 2inch recovery board that has no r-factor rating and which we in the field have found to be substandard) over roof area and screw down using disks and screws. Lay out . 0 rubber roof membrane cutting out all protrusions as we go such as: soil pipes penthouses skylights etc. Fold back rubber apply bonding adhesive to both insulation and to rubber membrane. Wait until tacky about 15 minutes. Then fold rubber over insulation to form a tight seal. - install pre-molded vent pipe boots to vent pipes where possible. - rubber flash all chimneys skylights and protrusions on roof with rubber flashing. - install a pressure treated wood edge nailer. Install . 032 heavy gauge metal to outside edges of roof and seal all nails with rubber edge flashing. -

979 South St Roslindale Ma
Strip and re-roof. Take down unused chimney.